Juniper Networks EX3200 Manual do Utilizador Página 270
- Página / 284
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
DC Power Grounding Requirements and Warning for EX Series Switches
An insulated grounding conductor that is identical in size to the grounded and
ungrounded branch circuit supply conductors but is identifiable by green and yellow
stripes is installed as part of the branch circuit that supplies the unit. The grounding
conductor is a separately derived system at the supply transformer or motor generator
set.
WARNING: When you install the switch, the ground connection must always be
made first and disconnected last.
Waarschuwing Bij de installatie van het toestel moet de aardverbinding altijd het
eerste worden gemaakt en het laatste worden losgemaakt.
Varoitus Laitetta asennettaessa on maahan yhdistäminen aina tehtävä ensiksi ja
maadoituksen irti kytkeminen viimeiseksi.
Attention Lors de l'installation de l'appareil, la mise à la terre doit toujours être
connectée en premier et déconnectée en dernier.
Warnung Der Erdanschluß muß bei der Installation der Einheit immer zuerst
hergestellt und zuletzt a/jointfilesconvert/51244/bgetrennt werden.
Avvertenza In fase di installazione dell'unità, eseguire sempre per primo il
collegamento a massa e disconnetterlo per ultimo.
Advarsel Når enheten installeres, må jordledningen alltid tilkobles først og frakobles
sist.
Aviso Ao instalar a unidade, a ligação à terra deverá ser sempre a primeira a ser
ligada, e a última a ser desligada.
¡Atención! Al instalar el equipo, conectar la tierra la primera y desconectarla la última.
Varning! Vid installation av enheten måste jordledningen alltid anslutas först och
kopplas bort sist.
Related Topics ■ General Safety Guidelines and Warnings for EX Series Switches on page 207
■ General Electrical Safety Guidelines and Warnings for EX Series Switches on
page 235
■ DC Power Electrical Safety Guidelines for EX Series Switches on page 241
■ DC Power Disconnection Warning for EX Series Switches on page 242
■ DC Power Wiring Sequence Warning for EX Series Switches on page 245
■ DC Power Wiring Terminations Warning for EX Series Switches on page 246
244 ■ DC Power Grounding Requirements and Warning for EX Series Switches
Complete Hardware Guide for EX3200 and EX4200 Ethernet Switches
- Switches 1
- END USER LICENSE AGREEMENT 3
- Table of Contents ■ ix 9
- Table of Contents 10
- Part 7 Returning Hardware 11
- Part 8 Safety Information 12
- Part 9 Compliance Information 13
- List of Figures 15
- List of Tables 19
- About This Topic Collection 21
- Software Topic Collections 22
- Downloading Software 23
- Documentation Symbols Key 23
- ■ Documentation Symbols Key 24
- Documentation Feedback 25
- Requesting Technical Support 25
- Opening a Case with JTAC 26
- Specifications 27
- Chapter 1 29
- EX3200 Switches 30
- Uplink Modules 31
- EX3200 Switch Models 32
- EX4200 Switch Models 32
- Component Descriptions 39
- LCD Panel Modes 40
- LCD Panel Menus 41
- AC OK LED is lit and 56
- SFP Uplink Module 60
- SFP+ Uplink Module 61
- XFP Uplink Module 62
- Figure 26: XFP Uplink Module 63
- Component Specifications 65
- EX3200 and EX4200 Switches 70
- Switches (continued) 82
- Site Preparation on page 81 105
- Site Preparation 107
- Chapter 4: Site Preparation 109
- Chapter 5 113
- ■ Cabinet size and clearance 115
- EX4200 Switches 117
- Cable Specifications 121
- Planning Power Requirements 123
- Figure 30: AC Plug Types 125
- Planning the Virtual Chassis 127
- Configuration 132
- Autoprovisioning 134
- Switch Components 137
- Installing the Switch 139
- QuantityComponent 142
- Mounting rack 146
- Mounting bracket 146
- ■ One pair of rear brackets 148
- Side-rail 149
- Rear brackets 150
- Front panel 152
- Rear panel 152
- Hang attached brackets 153
- Installing Switch Components 155
- ■ Cross-head screwdriver 164
- Connecting the Switch 167
- EX4200 Switch 174
- Configuring the Modem 182
- CON or CONSOLE) on 184
- Fiber-optic cable 185
- Transceiver 185
- Chapter 12 187
- Enter button 190
- 8. Click Next 191
- 11. Click Finish 191
- Enabling the Maintenance Menu 192
- 2. If the switch is running: 194
- Removing Switch Components 195
- ■ Needlenose pliers 204
- [edit interfaces] 206
- Different Switch 209
- Routine Maintenance 213
- Chapter 15 217
- Returning Hardware 221
- 196 ■ Returning Hardware 222
- Components 223
- Series Switches 225
- Safety Information 231
- 206 ■ Safety Information 232
- General Safety Information 233
- Radiation and Laser Warnings 239
- Class 1 Laser Product Warning 240
- Class 1 LED Product Warning 240
- Laser Beam Warning 241
- Information 245
- Battery Handling Warning 253
- Jewelry Removal Warning 254
- Lightning Activity Warning 256
- Operating Temperature Warning 257
- Product Disposal Warning 258
- Chapter 20 261
- Compliance Information 277
- 252 ■ Compliance Information 278
- European Community 281
- United States 281
- FCC Part 15 Statement 281
Manuais e produtos relacionados com Redes Juniper Networks EX3200
(176 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.046 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais