Juniper-networks M7I Manual do Utilizador

M7i Multiservice Edge Router PIC GuideOctober 2010This guide provides an overview and description of the PICs supported by the JuniperNetworks M7i Mul

M7i PIC Combination LimitationsIn most cases, you can install PICs of different media types in the M7i router. However,configuration rules might limit

T1 PIC (M7i Router)•Junos OS Release 6.0 and laterSoftware release•Four T1 ports•Power requirement: 0.08 A @ 48 V (3.7 W)•Supports clear channel T1 pe

RelatedDocumentationM7i PICs Description on page 3•• M7i PICs Supported on page 4• M7i PIC/CFEB Compatibility on page 11101Copyright © 2010, Juniper N

Tunnel Services PIC (M7i Router)•Junos OS Release 6.0 and laterSoftware release•Power requirement: 0.07 A @ 48 V (3.4 W)Description•Loopback function

Junos OS Documentation and Release NotesFor a list of related Junos OS documentation, seehttp://www.juniper.net/techpubs/software/junos/ .If the infor

To verify service entitlement by product serial number, use our Serial Number Entitlement(SNE) Tool: https://tools.juniper.net/SerialNumberEntitlement

29 June 2007—530-020806-01. Revision 1. Added SONET/SDH OC3c/STM1 with SFP,SONET/SDH OC3/STM1 (Multi-Rate) PIC with SFP, and SONET/SDH OC12/STM4(Multi

M7i PIC/CFEB CompatibilityThe PIC/CFEB compatibility matrixes list the current PICs for the m7I router. For example,Junos OS Release 9.4 is the first

Table 2: CFEB/PIC Compatibility in the M7i Router (continued)CFEB-ECFEBPortsPIC Model NumberPIC Family and Type10.2–1PE-1CHOC12STM4–IQE-SFP“Channelize

Table 2: CFEB/PIC Compatibility in the M7i Router (continued)CFEB-ECFEBPortsPIC Model NumberPIC Family and Type9.47.6R34PE-4GE-TYPE1-SFP-IQ2“Gigabit E

Adaptive Services II FIPS PIC (M7i Router)•Junos OS Release 7.2 and laterSoftware release•Junos-FIPS requires an Adaptive Services II FIPS PIC for ext

Status LED, one tricolor:•Off—PIC is offline and it is safe to remove it from the chassis.•Green—PIC is operating normally.•Yellow—PIC is initializing

ATM2 DS3 IQ PIC (M7i Router)•Junos OS Release 6.1 and laterSoftware release•Four DS3 ports•Power requirement: 0.41 A @ 48 V (20.0 W)•Intelligent queui

One tricolor per port:•Off—Not enabled•Green—Online with no alarms or failures•Yellow—Online with alarms for remote failures•Red—Active with a local a

ATM2 E3 IQ PIC (M7i Router)•Junos OS Release 6.1 and laterSoftware release•Two E3 ports•Power requirement: 0.41 A @ 48 V (20 W)•Intelligent queuing (I

•10 ft (3.05 m) posilock SMB to BNC (provided)•Four pairs of Rx and Tx coaxial cables•SONET/SDH OC3/STM1 fixed transceiver:•Multimode•Intermediate rea

Multiservices 100 PIC (M7i Router) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84SONET/SDH OC3c/STM1 PIC with SFP (M7i R

ATM2 OC3/STM1 IQ PIC (M7i Router)•Junos OS Release 6.0 and laterSoftware release•Two OC3 ports•Power requirement: 0.41 A @ 48 V (20 W)•Intelligent que

•Duplex SC/PC connector (RX and TX)•SONET/SDH OC3/STM1 fixed transceivers:•Multimode•Intermediate reach (IR-1)Optical interface specifications—see SON

ATM2 OC12/STM4 IQ PIC (M7i Router)•Junos OS Release 6.0 and laterSoftware release•One OC12 port•Power requirement: 0.41 A @ 48 V (20 W)•Intelligent qu

•Duplex SC/PC connector (Rx and Tx)•SONET/SDH OC12/STM4 fixed transceivers:•Multimode•Intermediate reach (IR-1)Optical interface specifications—see SO

Channelized DS3 IQ PIC (M7i Router)•Junos OS Release 6.0 and laterSoftware release•Four DS3 ports•Power requirement: 0.32 A @ 48 V (15.6 W)•Intelligen

One tricolor per port:•Off—Not enabled•Green—Online with no alarms or failures•Yellow—Online with alarms for remote failures•Red—Active with a local a

Channelized DS3 and E3 Enhanced IQ (IQE) PIC (M7i Router)RXRXRXRXSTATUSSTATUSSTATUSSTATUSRXRXRXTXTXTXTXRXPORT 1PORT0PORT1PORT2PORT3PORT 3PORT 2g006017

•Encapsulations:•Circuit cross-connect (CCC)•Translational cross-connect (TCC)•Extended Frame Relay for CCC and TCC•Flexible Frame Relay•Frame Relay•F

•Alarm reporting for error statistics and failure counts•DS1 alarms:•Alarm indication signal (AIS)•Loss of frame (LOF)•Remote alarm indication signal

Channelized E1 IQ PIC (M7i Router)•PE-10CHE1-RJ48-QPP-N: Junos OS Release 9.1R4, 9.2R3, 9.3R1 and laterSoftware release•Ten E1 ports•Power requirement

M7i PICs DescriptionPICs physically connect the router to network media. PICs receive incoming packets fromthe network and transmit outgoing packets t

•Alarm indication signal (AIS)•Loss of frame (LOF)•Out of frame (OOF)•Failed signal rate (FSR)Alarms, errors, andevents•Layer 2 per-queue and per-chan

Channelized E1/T1 Enhanced IQ (IQE) PIC (M7i Router)g006020•Junos OS Release 10.2 and later (Type 1)Software release•Ten E1 or T1 ports•DS1 and E1 int

•T1—CLI configurable as AMI or B8ZS•E1—HDB3•Encapsulations:•Circuit cross-connect (CCC)•Translational cross-connect (TCC)•Extended Frame Relay for CCC

•DS1 alarms:•Alarm indication signal (AIS)•Loss of frame (LOF)•Remote alarm indication signal (RAIS)•24-hour alarm reporting history maintained for er

Channelized OC3 IQ PIC (M7i Router)•Junos OS Release 7.6 and laterSoftware release•One OC3 port•Power requirement: 0.39 A @ 48 V (18.6 W)•Fine-grained

One tricolor per port:•Off—Not enabled•Green—Online with no alarms or failures•Yellow—Online with alarms for remote failures•Red—Active with a local a

Channelized OC3/STM1 Circuit Emulation PIC with SFP (M7i Router)•Junos OS Release 9.3 and laterSoftware release•Four OC3/STM1 ports•Power requirement:

•Loop timing•Optical diagnostics•AM1 or B8ZS line encoding•APS/SDH MSP•Fractional mode and framed clear channel mode•Superframe (D4/SF) and extended s

OK LED, one tricolor:•Off—PIC is offline and it is safe to remove it from the router.•Green—PIC is operating normally.•Yellow—PIC is initializing.•Red

Channelized OC3/STM1 Enhanced IQ (IQE) with SFP (M7i Router)STATUSPORT 1PORT 0TXTXRXRXg006019•Junos OS Release 10.2 and laterSoftware release•Two OC3

M7i PICs SupportedTable 1 on page 4 lists the PICs supported by the M7i router. The PICs are listedalphabetically by PIC family.Table 1: PICs Supporte

•Dynamic, arbitrary channel configuration•Quality of service (QoS) per channel: weighted round-robin (WRR), random early detection(RED), weighted rand

One tricolor Status LED per port:•Off—Not enabled•Green—Online with no alarms or failures•Yellow—Online with alarms for remote failures•Red—Active wit

•Phase lock loop (PLL)•Remote error indication (REI)•Severely errored frame (SEF)•Tributary unit—alarm indication signal (TU-AIS)•Tributary unit—loss

RelatedDocumentationM7i PICs Description on page 3•• M7i PICs Supported on page 4• M7i PIC/CFEB Compatibility on page 11• SONET/SDH OC3/STM1 Optical I

Channelized OC12 IQ PIC (M7i Router)•Junos OS Release 6.1 and laterSoftware release•One OC12 port•Power requirement: 0.23 A @ 48 V (10.8 W)•Intelligen

One tricolor per port:•Off—Not enabled•Green—Online with no alarms or failures•Yellow—Online with alarms for remote failures•Red—Active with a local a

Channelized OC12/STM4 Enhanced IQ (IQE) PIC with SFP (M7i Router)Figure 1: 1-Port IQE PICTXRXChannelizedSTM-4/OC-12 SFPg006014•Junos OS Release 10.2 a

•Quality of service (QoS) per channel: weighted round-robin (WRR), random early detection(RED), weighted random early detection (WRED)•Enhanced fine-g

•Duplex LC/PC connector (Rx and Tx); single-mode fiber•SONET/SDH OC12/STM4 fiber-optic SFP transceivers:•Short reach (model number: SFP-OC12-SR)•Inter

•Multiplex section—alarm indication signal (MS-AIS)•Multiplex section—far-end receive failure (MS-FERF)•Multiplex section—remote defect indication (MS

Table 1: PICs Supported in the M7i Router (continued)First Junos OSReleaseSupportConnectorModel NumberPortsPIC Family and Type6.0•Optical: SC/PCPE-1CH

•Layer 2 per-queue and per-channel packet and byte countersInstrumentation(counters)RelatedDocumentationM7i PICs Description on page 3•• M7i PICs Supp

Channelized STM1 IQ PIC (M7i Router)•Junos OS Release 6.0 and laterSoftware release•One STM1 port•Power requirement: 0.39 A @ 48 V (18.6 W)•Intelligen

•Alarm indication signal (AIS-L, AIS-P)•Bit error rate signal degrade (BERR-SD), bit error rate signal fail (BERR-SF)•Bit interleaved parity errors B1

Channelized T1 IQ PIC (M7i Router)•Junos OS Release 7.4 and laterSoftware release•Ten T1 ports•Power requirement: 0.15 A @ 48 V (7.2 W)•Intelligent qu

•Quality of service (QoS) per channel: weighted round-robin (WRR), random early detection(RED), weighted random early detection (WRED)•SNMP: T1 MIB an

DS3 PIC (M7i Router)•Junos OS Release 6.0 and laterSoftware release•Two or four DS3 ports•Power requirement: 0.47 A @ 48 V (22.5 W)•Integrated DSU int

•Alarm indication signal (AIS)•Bit error rate test (BERT) functionality on PIC (you can configure one DS3 channel in BERTmode and configure the remain

DS3/E3 Enhanced IQ (IQE) PIC (M7i Router)RXRXRXRXTXTXTXTXPORT0PORT1PORT2PORT3DS3/E3g006016•Junos OS Release 10.2 and laterSoftware release•Four DS3 or

•Flexible Frame Relay•Frame Relay•Frame Relay for CCC•Frame Relay for TCC•Frame Relay port CCC•High-Level Data Link Control (HDLC)•HDLC framing for CC

RelatedDocumentationM7i PICs Description on page 3•• M7i PICs Supported on page 4• M7i PIC/CFEB Compatibility on page 1159Copyright © 2010, Juniper Ne

Table 1: PICs Supported in the M7i Router (continued)First Junos OSReleaseSupportConnectorModel NumberPortsPIC Family and Type6.0•Custom 10 ft(3.05 m)

E1 PIC (M7i Router)•Junos OS Release 6.0 and laterSoftware release•Four E1 or coaxial ports•4-port, 120-ohm, RJ-48•4-port, 75-ohm, coaxial•Power requi

One tricolor per port:•Off—Not enabled•Green—Online with no alarms or failures•Yellow—Online with alarms for remote failures•Red—Active with a local a

E1/T1 Circuit Emulation PIC (M7i Router)•Junos OS Release 9.3 and laterSoftware release•Configurable as either twelve E1 ports or twelve T1 portsNOTE:

•PIC can be configured as twelve T1 ports or twelve E1 ports•Local and remote loopback diagnostics•E1 ports•High-performance throughput on each port a

OK LED, one tricolor:•Off—PIC is offline and it is safe to remove it from the router.•Green—PIC is operating normally.•Yellow—PIC is initializing.•Red

Structure agnostic alarms for T1:•Alarm indication signal (AIS)•Loss of signal (LOS)•Errored seconds (ES)•Line code violation (LCV)•Line errored secon

E3 PIC (M7i Router)•Junos OS Release 6.0 and laterSoftware release•Two E3 ports•Power requirement: 0.47 A @ 48 V (22.5 W)•Integrated DSU interoperabil

•Alarm indication signal (AIS)•Equipment failure (does not affect service)•Frame error•Line code violation•Loss of signal (LOS)•Out of frame (OOF)•Yel

E3 IQ PIC (M7i Router)•Junos OS Release 6.1 and laterSoftware release•Four E3 ports•Power requirement: 0.38 A @ 48 V (18 W)•Intelligent queuing (IQ) P

One tricolor per port:•Off—Not enabled•Green—Online with no alarms or failures•Yellow—Online with alarms for remote failures•Red—Active with a local a

Table 1: PICs Supported in the M7i Router (continued)First Junos OSReleaseSupportConnectorModel NumberPortsPIC Family and Type6.0•100-ohmRJ-48connecto

EIA-530 PIC (M7i Router)•Junos OS Release 6.0 and laterSoftware release•Two EIA-530, X.21 or V.35 serial ports•Power requirement: 0.07 A @ 48 V (3.4 W

Three bicolor per port:•Data set ready (DSR):•Green—DSR is detected or ignored•Red—DSR expected but not present•Data carrier detect (DCD):•Green—DCD i

ES PIC (M7i Router)•Junos OS Release 6.0 and laterSoftware release•High-bandwidth encryption (in accordance with IPSec standards)•Power requirement: 0

RelatedDocumentationM7i PICs Description on page 3•• M7i PICs Supported on page 4• M7i PIC/CFEB Compatibility on page 1173Copyright © 2010, Juniper Ne

Fast Ethernet PICs (M7i Router)Figure 3: 8-Port Fast Ethernet PICFigure 2: 4-Port Fast Ethernet PICFigure 5: VHDCI to RJ-21 cableFigure 4: 12-Port Fas

4-port PIC:•Connector: Two-pair, Category 5 unshielded twisted-pair connectivity through an RJ-45connector•Pinout: MDI noncrossover8-port PIC:•Connect

Gigabit Ethernet PIC with SFP (M7i Router)•Junos OS Release 6.3 and laterSoftware release•One Gigabit Ethernet port•Power requirement: 0.15 A @ 48 V (

Status LED, one bicolor:•Off—PIC is not enabled.•Green—PIC is operating normally.•Red—PIC has an error or failure.Port LEDs, one pair per port:•Link—I

Gigabit Ethernet IQ PIC with SFP (M7i Router)•Junos OS Release 6.0 and laterSoftware release•One Gigabit Ethernet port•Power requirement: 0.46 A @ 48

•Status LEDs, one tricolor:•Off—Not enabled.•Green—Online with no alarms or failures.•Yellow—Online with alarms for remote failures.•Red—Active with a

Table 1: PICs Supported in the M7i Router (continued)First Junos OSReleaseSupportConnectorModel NumberPortsPIC Family and TypeEthernet IQ27.6R3•Optica

Gigabit Ethernet IQ2 PIC with SFP (M7i Router)•Junos OS Release 7.6R3 and laterSoftware release•Four Gigabit Ethernet ports•Power requirement: 0.65 A

You can install any transceiver supported by the PIC.•Fiber-optic small form-factor pluggable (SFP) transceivers:•Duplex LC/PC connector (Rx and Tx)•1

Gigabit Ethernet Enhanced IQ2 (IQ2E) PIC with SFP (M7i Router)g004424•Junos OS Release 9.4 and laterSoftware release•Four Gigabit Ethernet ports•Power

•You can install any transceiver supported by the PIC.•Fiber-optic small form-factor pluggable (SFP) transceivers:•Duplex LC/PC connector (Rx and Tx)•

Multiservices 100 PIC (M7i Router)•Junos OS Release 8.1 and laterSoftware release•Supports tunnel services. This feature is included with the PIC and

Table 3: Multiservices PICs Software Features Supported by the M7i Router (continued)Multiservices 100Software Feature8.1Network Address Translation (

SONET/SDH OC3c/STM1 PIC with SFP (M7i Router)•Junos OS Release 8.4 and laterSoftware release•Two OC3c ports•Power requirement: 0.25 A @ 48 V (12 W)Des

One tricolor per port:•Off—Not enabled•Green—Online with no alarms or failures•Yellow—Online with alarms for remote failures•Red—Active with a local a

• M7i PIC/CFEB Compatibility on page 11• SONET/SDH OC3/STM1 Optical Interface SpecificationsCopyright © 2010, Juniper Networks, Inc.88M7i Multiservice

SONET/SDH OC3/STM1 Enhanced IQ (IQE) PIC with SFP (M7i Router)STM-1/OC-3 SFPg006018•Junos OS Release 10.2 and later (Type 1)Software release•Four DS3

Table 1: PICs Supported in the M7i Router (continued)First Junos OSReleaseSupportConnectorModel NumberPortsPIC Family and Type6.0•Two DB-25maleconnect

•Flexible Frame Relay•Frame Relay•Frame Relay for CCC•Frame Relay for TCC•Frame Relay port CCC•High-Level Data Link Control (HDLC)•HDLC framing for CC

RelatedDocumentationM7i PICs Description on page 3•• M7i PICs Supported on page 4• M7i PIC/CFEB Compatibility on page 11SONET/SDH OC3/STM1 (Multi-Rate

You can install any transceiver supported by the PIC.•Duplex LC/PC connector (Rx and Tx)•SONET/SDH OC3/STM1 small form-factor pluggable (SFP) transcei

•SONET alarms:•Alarm indication signal—line (AIS-L)•Alarm indication signal—path (AIS-P)•Bit error rate signal degrade (BERR-SD)•Bit error rate signal

SONET/SDH OC12/STM4 Enhanced IQ (IQE) PIC with SFP (M7i Router)TXRXSTM-4/OC-12 SFPg006015•Junos OS Release 10.2 and later (Type 1)Software release•One

•Duplex LC/PC connector (Rx and Tx)•SONET/SDH OC12/STM4 fiber-optic SFP transceivers:•Short reach (model number: SFP-OC12-SR)•Intermediate reach (IR-1

•SONET alarms:•Alarm indication signal—line (AIS-L)•Alarm indication signal—path (AIS-P)•Bit error rate signal degrade (BERR-SD)•Bit error rate signal

SONET/SDH OC12/STM4 (Multi-Rate) PIC with SFP (M7i Router)•Junos OS Release 8.4 and laterSoftware release•Rate-selectable using one of the following r

You can install any transceiver supported by the PIC.•Duplex LC/PC connector (Rx and Tx)•SONET/SDH OC3/STM1 small form-factor pluggable (SFP) transcei

•SONET alarms:•Alarm indication signal—line (AIS-L)•Alarm indication signal—path (AIS-P)•Bit error rate signal degrade (BERR-SD)•Bit error rate signal